Page 1 of 1

Supercharged and Turbocharged Jimny

Posted: Sat Jan 04, 2020 7:48 pm
by Keith Phillips
It all starts with buying a Swift Sport M16A VVT.

Compression ratio is a little high so it gets 9.0:1 Wiseco Pistons.

The con-rods are a little weak so it got K1 H beam rods installed.

A 0.5mm rebore brings the capacity to exactly 1600CC and leaves room for future reboring.

All the nuts and bolts on the cylinder head and crank were changed to ARP high strength ones.

A new trigger wheel was laser cut and installed for the Megasquirt MS3 to use the original crank sensor
and the cam had the trigger modified to leave a single trigger for sequential ignition and EFI.
20190527_211925.jpg
20190527_211925.jpg (4.95 MiB) Viewed 2949 times
20190528_202551.jpg
20190528_202551.jpg (4.06 MiB) Viewed 2949 times
20190528_202547.jpg
20190528_202547.jpg (4.39 MiB) Viewed 2949 times
Some pictures taken while figuring things out on the supercharger side.




20190602_171650.jpg
20190602_171650.jpg (4.54 MiB) Viewed 2949 times
20190602_135737.jpg
20190602_135737.jpg (3.76 MiB) Viewed 2949 times
20190602_135739.jpg
20190602_135739.jpg (4.02 MiB) Viewed 2949 times
Flange for the Turbo manifold.
20190615_213932.jpg
20190615_213932.jpg (5.01 MiB) Viewed 2949 times


The mount figured and fitted on the engine.
20190714_125131.jpg
20190714_125131.jpg (4.94 MiB) Viewed 2949 times
20190713_164130.jpg
20190713_164130.jpg (2.01 MiB) Viewed 2949 times
Programmed in Mastercam
20190713_121425.jpg
20190713_121425.jpg (3.75 MiB) Viewed 2949 times
Insulating spacer for the Jenvey inlet manifold.
20190710_200139.jpg
20190710_200139.jpg (4.9 MiB) Viewed 2949 times
Newer cam cover means COPs and no coil cover.
Made one and painted it wrinkle finish black.
20191214_171439.jpg
20191214_171439.jpg (4.3 MiB) Viewed 2949 times
20200104_163848.jpg
20200104_163848.jpg (3.75 MiB) Viewed 2949 times
20200104_120725.jpg
20200104_120725.jpg (3.77 MiB) Viewed 2949 times

Onto the Turbo Side.

Making a start on the manifold.
20190718_201212.jpg
20190718_201212.jpg (5.27 MiB) Viewed 2949 times
20191222_161644.jpg
20191222_161644.jpg (3.53 MiB) Viewed 2949 times
20191227_135119.jpg
20191227_135119.jpg (3.77 MiB) Viewed 2949 times
Probably going to plumb the external wastegate into the exhaust.....for peace!

Re: Supercharged and Turbocharged Jimny

Posted: Sat Jan 04, 2020 8:09 pm
by Jack
My god that looks beautiful :P
Are we guessing hp matey i say 240

Re: Supercharged and Turbocharged Jimny

Posted: Wed Jan 08, 2020 12:43 pm
by Tom
Incredible, can't wait to see this progress.

Re: Supercharged and Turbocharged Jimny

Posted: Sun Jan 12, 2020 10:42 am
by Keith Phillips
Bit of bling and the top is just about finished.
20200110_183845.jpg
20200110_183845.jpg (3.9 MiB) Viewed 2806 times

Re: Supercharged and Turbocharged Jimny

Posted: Thu Jan 16, 2020 10:16 pm
by The Cameraman
Wow,

what beautiful work.

Re: Supercharged and Turbocharged Jimny

Posted: Sun Feb 16, 2020 8:22 pm
by Keith Phillips
20200216_191357.jpg
Supercharger belt drive started.