Supercharged and Turbocharged Jimny

Post Reply
Keith Phillips
Site Admin
Posts: 31
Joined: Wed Jul 24, 2019 11:24 pm

Supercharged and Turbocharged Jimny

Post by Keith Phillips »

It all starts with buying a Swift Sport M16A VVT.

Compression ratio is a little high so it gets 9.0:1 Wiseco Pistons.

The con-rods are a little weak so it got K1 H beam rods installed.

A 0.5mm rebore brings the capacity to exactly 1600CC and leaves room for future reboring.

All the nuts and bolts on the cylinder head and crank were changed to ARP high strength ones.

A new trigger wheel was laser cut and installed for the Megasquirt MS3 to use the original crank sensor
and the cam had the trigger modified to leave a single trigger for sequential ignition and EFI.
20190527_211925.jpg
20190527_211925.jpg (4.95 MiB) Viewed 213992 times
20190528_202551.jpg
20190528_202551.jpg (4.06 MiB) Viewed 213992 times
20190528_202547.jpg
20190528_202547.jpg (4.39 MiB) Viewed 213992 times
Some pictures taken while figuring things out on the supercharger side.




20190602_171650.jpg
20190602_171650.jpg (4.54 MiB) Viewed 213992 times
20190602_135737.jpg
20190602_135737.jpg (3.76 MiB) Viewed 213992 times
20190602_135739.jpg
20190602_135739.jpg (4.02 MiB) Viewed 213992 times
Flange for the Turbo manifold.
20190615_213932.jpg
20190615_213932.jpg (5.01 MiB) Viewed 213992 times


The mount figured and fitted on the engine.
20190714_125131.jpg
20190714_125131.jpg (4.94 MiB) Viewed 213992 times
20190713_164130.jpg
20190713_164130.jpg (2.01 MiB) Viewed 213992 times
Programmed in Mastercam
20190713_121425.jpg
20190713_121425.jpg (3.75 MiB) Viewed 213992 times
Insulating spacer for the Jenvey inlet manifold.
20190710_200139.jpg
20190710_200139.jpg (4.9 MiB) Viewed 213992 times
Newer cam cover means COPs and no coil cover.
Made one and painted it wrinkle finish black.
20191214_171439.jpg
20191214_171439.jpg (4.3 MiB) Viewed 213992 times
20200104_163848.jpg
20200104_163848.jpg (3.75 MiB) Viewed 213992 times
20200104_120725.jpg
20200104_120725.jpg (3.77 MiB) Viewed 213992 times

Onto the Turbo Side.

Making a start on the manifold.
20190718_201212.jpg
20190718_201212.jpg (5.27 MiB) Viewed 213992 times
20191222_161644.jpg
20191222_161644.jpg (3.53 MiB) Viewed 213992 times
20191227_135119.jpg
20191227_135119.jpg (3.77 MiB) Viewed 213992 times
Probably going to plumb the external wastegate into the exhaust.....for peace!
Jack
Posts: 1
Joined: Mon Jul 29, 2019 7:05 am

Re: Supercharged and Turbocharged Jimny

Post by Jack »

My god that looks beautiful :P
Are we guessing hp matey i say 240
Tom
Posts: 2
Joined: Wed Dec 18, 2019 9:35 pm

Re: Supercharged and Turbocharged Jimny

Post by Tom »

Incredible, can't wait to see this progress.
Keith Phillips
Site Admin
Posts: 31
Joined: Wed Jul 24, 2019 11:24 pm

Re: Supercharged and Turbocharged Jimny

Post by Keith Phillips »

Bit of bling and the top is just about finished.
20200110_183845.jpg
20200110_183845.jpg (3.9 MiB) Viewed 213849 times
The Cameraman
Posts: 2
Joined: Thu Jan 16, 2020 6:05 pm

Re: Supercharged and Turbocharged Jimny

Post by The Cameraman »

Wow,

what beautiful work.
Keith Phillips
Site Admin
Posts: 31
Joined: Wed Jul 24, 2019 11:24 pm

Re: Supercharged and Turbocharged Jimny

Post by Keith Phillips »

20200216_191357.jpg
Supercharger belt drive started.
Ruamann
Posts: 1
Joined: Fri Dec 02, 2022 7:02 pm

Re: Supercharged and Turbocharged Jimny

Post by Ruamann »

Just amazing, like. Giz it haha.
Post Reply