Starting Point

As many details as I can remember of the process I used.
Post Reply
Keith Phillips
Site Admin
Posts: 31
Joined: Wed Jul 24, 2019 11:24 pm

Starting Point

Post by Keith Phillips »

Heres the Jimny loaded on a truck.
IMG-20170616-WA0007.jpg
IMG-20170616-WA0007.jpg (240.22 KiB) Viewed 15793 times
IMG-20170616-WA0006.jpg
IMG-20170616-WA0006.jpg (219.87 KiB) Viewed 15793 times
So anyhoo.

I set about cutting the rear off.
20180415_183933.jpg
20180415_183933.jpg (1.72 MiB) Viewed 15793 times
I made the cut 90mm back from the door shut line.....trimmed the outer and then pondered the inner.

So there are three layers of metal to be cut through and then be joined back together....homogenous like.

My cunning plan was to weld the inner and outer to the outer edges of a 16g strip....and weld through the holes to tie in the centre panel.
20180415_194225.jpg
20180415_194225.jpg (1.94 MiB) Viewed 15793 times
20180416_201759.jpg
20180416_201759.jpg (1.92 MiB) Viewed 15793 times
Never forget the seatbelt needs to go back in and to feel safe it needs to be a secure item.
20180418_205725.jpg
20180418_205725.jpg (1.74 MiB) Viewed 15793 times
So with that done I moved to the corner trims.

I stripped the rear door out fully....it can be lifted with a little finger at that point.
I loosely fitted it with a few tacks and made a couple of panels as can be seen here.
20180426_204525.jpg
20180426_204525.jpg (1.82 MiB) Viewed 15793 times
Next was to make a rear panel....some corrugations and a little bit of fancy to make it easier on the eye.
20180428_181101.jpg
20180428_181101.jpg (1.79 MiB) Viewed 15793 times
Further trim panels made and fitted to ease the transition.
20180430_200505.jpg
20180430_200505.jpg (1.78 MiB) Viewed 15793 times
I've never liked the way that the Jimny trayback is finished at the rear corners so I gave my take on how I'd like it.
20180513_190244.jpg
20180513_190244.jpg (2.01 MiB) Viewed 15793 times
So with the back closed back to the inside.....some panels needed.
20180506_173635.jpg
20180506_173635.jpg (1.89 MiB) Viewed 15793 times
Still remembering the seatbelt has to go back in and that I want to put some trim back in to tidy it up a little.
20180506_183334.jpg
20180506_183334.jpg (1.88 MiB) Viewed 15793 times
The measurements on the panel were for cutting it out of what was left of the rear inner panel.

A little further along.
20180507_180622.jpg
20180507_180622.jpg (2.08 MiB) Viewed 15793 times
Seatbelt has a home so I decided to reduce the noise levels in the cab.
20180517_195258.jpg
20180517_195258.jpg (2.2 MiB) Viewed 15793 times
Roof done...
20180522_201934.jpg
20180522_201934.jpg (484.09 KiB) Viewed 15793 times
Bulkhead done.
20180520_191233.jpg
20180520_191233.jpg (2.55 MiB) Viewed 15793 times
Rear panel done....floor too.....got to be quieter!....surely?

Time to weld the holes in the doors and sills..
20180526_184403.jpg
20180526_184403.jpg (1.46 MiB) Viewed 15793 times
20180510_212850.jpg
20180510_212850.jpg (1.72 MiB) Viewed 15793 times
Fill prime etc..
20180526_204347.jpg
20180526_204347.jpg (525.31 KiB) Viewed 15793 times
20180609_184202.jpg
20180609_184202.jpg (2.49 MiB) Viewed 15793 times
Painted....still ongoing!
20180616_114614.jpg
20180616_114614.jpg (2.29 MiB) Viewed 15793 times
20180616_114641.jpg
20180616_114641.jpg (2.75 MiB) Viewed 15793 times
20180615_192536.jpg
20180615_192536.jpg (2.12 MiB) Viewed 15793 times
20180617_175203.jpg
20180617_175203.jpg (2.37 MiB) Viewed 15793 times
Not quite worked to the bone.....got to the blood!
20180610_163312.jpg
20180610_163312.jpg (467.8 KiB) Viewed 15793 times
Undersealed the front end.
20180610_182157.jpg
20180610_182157.jpg (1.72 MiB) Viewed 15793 times
Keith Phillips
Site Admin
Posts: 31
Joined: Wed Jul 24, 2019 11:24 pm

Re: Starting Point

Post by Keith Phillips »

Bye bye patchy paint....I ran out of paint last year....got busy from then on and finally got this sorted this week.
20190805_141046.jpg
20190805_141046.jpg (5.04 MiB) Viewed 15789 times
Made a fairing for the CB and Dab/analogue aerials.
20190805_180056.jpg
20190805_180056.jpg (3.63 MiB) Viewed 15789 times
Keith Phillips
Site Admin
Posts: 31
Joined: Wed Jul 24, 2019 11:24 pm

Re: Starting Point

Post by Keith Phillips »

A new development for traybacking.....should be a weekend job to fit when I finalise it.
cabrear.jpg
Post Reply